php connect กับ hard ware board Ft232 UART ได้ป่าวคะ

สำหรับผู้ที่ เริ่มต้น Programming - PHP มีอะไร แนะนำ หรือข้อสงสัยต้องบอร์ด นี้ คนที่มีความรู้ แบ่งปันคนอื่นบ้างนะ ปัญหาการเขียนโปรแกรม แบบ OOP Session Cookies php network

Moderator: mindphp, ผู้ดูแลกระดาน

nutchafoh
PHP Newbie
PHP Newbie
โพสต์: 1
ลงทะเบียนเมื่อ: 19/09/2011 2:44 pm

php connect กับ hard ware board Ft232 UART ได้ป่าวคะ

โพสต์ที่ยังไม่ได้อ่าน โดย nutchafoh »

คืออยากจะทราบว่า php สามารถรับ ส่งข้อมูลของ บอร์ด FT232 UART ผ่านทาง COM Port ของ Linux ได้ป่าวอ่ะ คือใช้ code
<?
$a=fopen('/dev/ttyUSB0','a+');
$w=fwrite($a,'$string');//ส่งค่า string ให้ board เริ่มทำการส่งข้อมูล
$i=1;
while($b=fread($a,1024)!=EOF){//ให้อ่านทีละ 1024 byte
echo $b; // แสดงค่าที่อ่าน
$i++;
if($i==2500){
fwrite($a,'$string'); //ส่งค่า string ให้ board หยุดการส่งข้อมูล
brake;
}
}
fclose($a);
?>

ผลลัพธ์คือ

ค่าที่ได้จาก board แต่บางครั้งมันมาไม่ครบอะค่ะแล้วบางครั้งมันไม่ออกจาก loop ด้วยอ่ะ

รบกวนช่วยทีนะคะ
ขอบคุนคะ
ภาพประจำตัวสมาชิก
mindphp
ผู้ดูแลระบบ MindPHP
ผู้ดูแลระบบ MindPHP
โพสต์: 41232
ลงทะเบียนเมื่อ: 22/09/2008 6:18 pm
ติดต่อ:

Re: php connect กับ hard ware board Ft232 UART ได้ป่าวคะ

โพสต์ที่ยังไม่ได้อ่าน โดย mindphp »

ลองใช้ Class นี้ช่วยครับ

<?php
define ("SERIAL_DEVICE_NOTSET", 0);
define ("SERIAL_DEVICE_SET", 1);
define ("SERIAL_DEVICE_OPENED", 2);

/**
* Serial port control class
*
* THIS PROGRAM COMES WITH ABSOLUTELY NO WARANTIES !
* USE IT AT YOUR OWN RISKS !
*
* @author Rémy Sanchez <[email protected]>
* @thanks Aurélien Derouineau for finding how to open serial ports with windows
* @thanks Alec Avedisyan for help and testing with reading
* @copyright under GPL 2 licence
*/
class phpSerial
{
var $_device = null;
var $_windevice = null;
var $_dHandle = null;
var $_dState = SERIAL_DEVICE_NOTSET;
var $_buffer = "";
var $_os = "";

/**
* This var says if buffer should be flushed by sendMessage (true) or manualy (false)
*
* @var bool
*/
var $autoflush = true;

/**
* Constructor. Perform some checks about the OS and setserial
*
* @return phpSerial
*/
function phpSerial ()
{
setlocale(LC_ALL, "en_US");

$sysname = php_uname();

if (substr($sysname, 0, 5) === "Linux")
{
$this->_os = "linux";

if($this->_exec("stty --version") === 0)
{
register_shutdown_function(array($this, "deviceClose"));
}
else
{
trigger_error("No stty availible, unable to run.", E_USER_ERROR);
}
}
elseif(substr($sysname, 0, 7) === "Windows")
{
$this->_os = "windows";
register_shutdown_function(array($this, "deviceClose"));
}
else
{
trigger_error("Host OS is neither linux nor windows, unable tu run.", E_USER_ERROR);
exit();
}
}

//
// OPEN/CLOSE DEVICE SECTION -- {START}
//

/**
* Device set function : used to set the device name/address.
* -> linux : use the device address, like /dev/ttyS0
* -> windows : use the COMxx device name, like COM1 (can also be used
* with linux)
*
* @param string $device the name of the device to be used
* @return bool
*/
function deviceSet ($device)
{
if ($this->_dState !== SERIAL_DEVICE_OPENED)
{
if ($this->_os === "linux")
{
if (preg_match("@^COM(\d+):?$@i", $device, $matches))
{
$device = "/dev/ttyS" . ($matches[1] - 1);
}

if ($this->_exec("stty -F " . $device) === 0)
{
$this->_device = $device;
$this->_dState = SERIAL_DEVICE_SET;
return true;
}
}
elseif ($this->_os === "windows")
{
if (preg_match("@^COM(\d+):?$@i", $device, $matches) and $this->_exec(exec("mode " . $device)) === 0)
{
$this->_windevice = "COM" . $matches[1];
$this->_device = "\\.\com" . $matches[1];
$this->_dState = SERIAL_DEVICE_SET;
return true;
}
}

trigger_error("Specified serial port is not valid", E_USER_WARNING);
return false;
}
else
{
trigger_error("You must close your device before to set an other one", E_USER_WARNING);
return false;
}
}

/**
* Opens the device for reading and/or writing.
*
* @param string $mode Opening mode : same parameter as fopen()
* @return bool
*/
function deviceOpen ($mode = "r+b")
{
if ($this->_dState === SERIAL_DEVICE_OPENED)
{
trigger_error("The device is already opened", E_USER_NOTICE);
return true;
}

if ($this->_dState === SERIAL_DEVICE_NOTSET)
{
trigger_error("The device must be set before to be open", E_USER_WARNING);
return false;
}

if (!preg_match("@^[raw]\+?b?$@", $mode))
{
trigger_error("Invalid opening mode : ".$mode.". Use fopen() modes.", E_USER_WARNING);
return false;
}

$this->_dHandle = @fopen($this->_device, $mode);

if ($this->_dHandle !== false)
{
stream_set_blocking($this->_dHandle, 0);
$this->_dState = SERIAL_DEVICE_OPENED;
return true;
}

$this->_dHandle = null;
trigger_error("Unable to open the device", E_USER_WARNING);
return false;
}

/**
* Closes the device
*
* @return bool
*/
function deviceClose ()
{
if ($this->_dState !== SERIAL_DEVICE_OPENED)
{
return true;
}

if (fclose($this->_dHandle))
{
$this->_dHandle = null;
$this->_dState = SERIAL_DEVICE_SET;
return true;
}

trigger_error("Unable to close the device", E_USER_ERROR);
return false;
}

//
// OPEN/CLOSE DEVICE SECTION -- {STOP}
//

//
// CONFIGURE SECTION -- {START}
//

/**
* Configure the Baud Rate
* Possible rates : 110, 150, 300, 600, 1200, 2400, 4800, 9600, 38400,
* 57600 and 115200.
*
* @param int $rate the rate to set the port in
* @return bool
*/
function confBaudRate ($rate)
{
if ($this->_dState !== SERIAL_DEVICE_SET)
{
trigger_error("Unable to set the baud rate : the device is either not set or opened", E_USER_WARNING);
return false;
}

$validBauds = array (
110 => 11,
150 => 15,
300 => 30,
600 => 60,
1200 => 12,
2400 => 24,
4800 => 48,
9600 => 96,
19200 => 19,
38400 => 38400,
57600 => 57600,
115200 => 115200
);

if (isset($validBauds[$rate]))
{
if ($this->_os === "linux")
{
$ret = $this->_exec("stty -F " . $this->_device . " " . (int) $rate, $out);
}
elseif ($this->_os === "windows")
{
$ret = $this->_exec("mode " . $this->_windevice . " BAUD=" . $validBauds[$rate], $out);
}
else return false;

if ($ret !== 0)
{
trigger_error ("Unable to set baud rate: " . $out[1], E_USER_WARNING);
return false;
}
}
}

/**
* Configure parity.
* Modes : odd, even, none
*
* @param string $parity one of the modes
* @return bool
*/
function confParity ($parity)
{
if ($this->_dState !== SERIAL_DEVICE_SET)
{
trigger_error("Unable to set parity : the device is either not set or opened", E_USER_WARNING);
return false;
}

$args = array(
"none" => "-parenb",
"odd" => "parenb parodd",
"even" => "parenb -parodd",
);

if (!isset($args[$parity]))
{
trigger_error("Parity mode not supported", E_USER_WARNING);
return false;
}

if ($this->_os === "linux")
{
$ret = $this->_exec("stty -F " . $this->_device . " " . $args[$parity], $out);
}
else
{
$ret = $this->_exec("mode " . $this->_windevice . " PARITY=" . $parity{0}, $out);
}

if ($ret === 0)
{
return true;
}

trigger_error("Unable to set parity : " . $out[1], E_USER_WARNING);
return false;
}

/**
* Sets the length of a character.
*
* @param int $int length of a character (5 <= length <= 8)
* @return bool
*/
function confCharacterLength ($int)
{
if ($this->_dState !== SERIAL_DEVICE_SET)
{
trigger_error("Unable to set length of a character : the device is either not set or opened", E_USER_WARNING);
return false;
}

$int = (int) $int;
if ($int < 5) $int = 5;
elseif ($int > 8) $int = 8;

if ($this->_os === "linux")
{
$ret = $this->_exec("stty -F " . $this->_device . " cs" . $int, $out);
}
else
{
$ret = $this->_exec("mode " . $this->_windevice . " DATA=" . $int, $out);
}

if ($ret === 0)
{
return true;
}

trigger_error("Unable to set character length : " .$out[1], E_USER_WARNING);
return false;
}

/**
* Sets the length of stop bits.
*
* @param float $length the length of a stop bit. It must be either 1,
* 1.5 or 2. 1.5 is not supported under linux and on some computers.
* @return bool
*/
function confStopBits ($length)
{
if ($this->_dState !== SERIAL_DEVICE_SET)
{
trigger_error("Unable to set the length of a stop bit : the device is either not set or opened", E_USER_WARNING);
return false;
}

if ($length != 1 and $length != 2 and $length != 1.5 and !($length == 1.5 and $this->_os === "linux"))
{
trigger_error("Specified stop bit length is invalid", E_USER_WARNING);
return false;
}

if ($this->_os === "linux")
{
$ret = $this->_exec("stty -F " . $this->_device . " " . (($length == 1) ? "-" : "") . "cstopb", $out);
}
else
{
$ret = $this->_exec("mode " . $this->_windevice . " STOP=" . $length, $out);
}

if ($ret === 0)
{
return true;
}

trigger_error("Unable to set stop bit length : " . $out[1], E_USER_WARNING);
return false;
}

/**
* Configures the flow control
*
* @param string $mode Set the flow control mode. Availible modes :
* -> "none" : no flow control
* -> "rts/cts" : use RTS/CTS handshaking
* -> "xon/xoff" : use XON/XOFF protocol
* @return bool
*/
function confFlowControl ($mode)
{
if ($this->_dState !== SERIAL_DEVICE_SET)
{
trigger_error("Unable to set flow control mode : the device is either not set or opened", E_USER_WARNING);
return false;
}

$linuxModes = array(
"none" => "clocal -crtscts -ixon -ixoff",
"rts/cts" => "-clocal crtscts -ixon -ixoff",
"xon/xoff" => "-clocal -crtscts ixon ixoff"
);
$windowsModes = array(
"none" => "xon=off octs=off rts=on",
"rts/cts" => "xon=off octs=on rts=hs",
"xon/xoff" => "xon=on octs=off rts=on",
);

if ($mode !== "none" and $mode !== "rts/cts" and $mode !== "xon/xoff") {
trigger_error("Invalid flow control mode specified", E_USER_ERROR);
return false;
}

if ($this->_os === "linux")
$ret = $this->_exec("stty -F " . $this->_device . " " . $linuxModes[$mode], $out);
else
$ret = $this->_exec("mode " . $this->_windevice . " " . $windowsModes[$mode], $out);

if ($ret === 0) return true;
else {
trigger_error("Unable to set flow control : " . $out[1], E_USER_ERROR);
return false;
}
}

/**
* Sets a setserial parameter (cf man setserial)
* NO MORE USEFUL !
* -> No longer supported
* -> Only use it if you need it
*
* @param string $param parameter name
* @param string $arg parameter value
* @return bool
*/
function setSetserialFlag ($param, $arg = "")
{
if (!$this->_ckOpened()) return false;

$return = exec ("setserial " . $this->_device . " " . $param . " " . $arg . " 2>&1");

if ($return{0} === "I")
{
trigger_error("setserial: Invalid flag", E_USER_WARNING);
return false;
}
elseif ($return{0} === "/")
{
trigger_error("setserial: Error with device file", E_USER_WARNING);
return false;
}
else
{
return true;
}
}

//
// CONFIGURE SECTION -- {STOP}
//

//
// I/O SECTION -- {START}
//

/**
* Sends a string to the device
*
* @param string $str string to be sent to the device
* @param float $waitForReply time to wait for the reply (in seconds)
*/
function sendMessage ($str, $waitForReply = 0.1)
{
$this->_buffer .= $str;

if ($this->autoflush === true) $this->flush();

usleep((int) ($waitForReply * 1000000));
}

/**
* Reads the port until no new datas are availible, then return the content.
*
* @pararm int $count number of characters to be read (will stop before
* if less characters are in the buffer)
* @return string
*/
function readPort ($count = 0)
{
if ($this->_dState !== SERIAL_DEVICE_OPENED)
{
trigger_error("Device must be opened to read it", E_USER_WARNING);
return false;
}

if ($this->_os === "linux")
{
$content = ""; $i = 0;

if ($count !== 0)
{
do {
if ($i > $count) $content .= fread($this->_dHandle, ($count - $i));
else $content .= fread($this->_dHandle, 128);
} while (($i += 128) === strlen($content));
}
else
{
do {
$content .= fread($this->_dHandle, 128);
} while (($i += 128) === strlen($content));
}

return $content;
}
elseif ($this->_os === "windows")
{
/* Do nohting : not implented yet */
}

trigger_error("Reading serial port is not implemented for Windows", E_USER_WARNING);
return false;
}

/**
* Flushes the output buffer
*
* @return bool
*/
function flush ()
{
if (!$this->_ckOpened()) return false;

if (fwrite($this->_dHandle, $this->_buffer) !== false)
{
$this->_buffer = "";
return true;
}
else
{
$this->_buffer = "";
trigger_error("Error while sending message", E_USER_WARNING);
return false;
}
}

//
// I/O SECTION -- {STOP}
//

//
// INTERNAL TOOLKIT -- {START}
//

function _ckOpened()
{
if ($this->_dState !== SERIAL_DEVICE_OPENED)
{
trigger_error("Device must be opened", E_USER_WARNING);
return false;
}

return true;
}

function _ckClosed()
{
if ($this->_dState !== SERIAL_DEVICE_CLOSED)
{
trigger_error("Device must be closed", E_USER_WARNING);
return false;
}

return true;
}

function _exec($cmd, &$out = null)
{
$desc = array(
1 => array("pipe", "w"),
2 => array("pipe", "w")
);

$proc = proc_open($cmd, $desc, $pipes);

$ret = stream_get_contents($pipes[1]);
$err = stream_get_contents($pipes[2]);

fclose($pipes[1]);
fclose($pipes[2]);

$retVal = proc_close($proc);

if (func_num_args() == 2) $out = array($ret, $err);
return $retVal;
}

//
// INTERNAL TOOLKIT -- {STOP}
//
}
?>

เขียนโดย * @author Rémy Sanchez <[email protected]>
ติดตาม VDO: http://www.youtube.com/c/MindphpVideoman
ติดตาม FB: https://www.facebook.com/pages/MindphpC ... 9517401606
หมวดแชร์ความรู้: https://www.mindphp.com/forums/viewforum.php?f=29
รับอบรม และพัฒนาระบบ: https://www.mindphp.com/forums/viewtopic.php?f=6&t=2042
ภาพประจำตัวสมาชิก
mindphp
ผู้ดูแลระบบ MindPHP
ผู้ดูแลระบบ MindPHP
โพสต์: 41232
ลงทะเบียนเมื่อ: 22/09/2008 6:18 pm
ติดต่อ:

Re: php connect กับ hard ware board Ft232 UART ได้ป่าวคะ

โพสต์ที่ยังไม่ได้อ่าน โดย mindphp »

ตัวอย่างการใช้

โค้ด: เลือกทั้งหมด

<?php
include "php_serial.class.php";

// Let's start the class
$serial = new phpSerial;

// First we must specify the device. This works on both linux and windows (if
// your linux serial device is /dev/ttyS0 for COM1, etc)
$serial->deviceSet("COM1");

// Then we need to open it
$serial->deviceOpen();

// To write into
$serial->sendMessage("Hello !");

// Or to read from
$read = $serial->readPort();

// If you want to change the configuration, the device must be closed
$serial->deviceClose();

// We can change the baud rate
$serial->confBaudRate(2400);

// etc...
?> 
ติดตาม VDO: http://www.youtube.com/c/MindphpVideoman
ติดตาม FB: https://www.facebook.com/pages/MindphpC ... 9517401606
หมวดแชร์ความรู้: https://www.mindphp.com/forums/viewforum.php?f=29
รับอบรม และพัฒนาระบบ: https://www.mindphp.com/forums/viewtopic.php?f=6&t=2042
ตอบกลับโพส
  • Similar Topics
    ตอบกลับ
    แสดง
    โพสต์ล่าสุด

ผู้ใช้งานขณะนี้

สมาชิกกำลังดูบอร์ดนี้: Amazon [Bot] และบุคลทั่วไป 119